Either of
the following options will clean waste and or virgin vegetable
oil used motor oil or Biodiesel in the wash process.
For proper
centrifuge operation the oil must be heated to 140-180 F.
Multiple passes will be needed depending on the degree of
contamination.
In most
cases "rough" filtering with a 100 mesh (140 micron) strainer
is required initially. Then 3-4 turns of the volume through
the centrifuge in most cases will give optimum results and a
better finished product,
To remove glycerin at the end of the process no heat is
needed. More than one pass may be needed.
Centrifuges are not a methanol recovery device.
Centrifuges can not be used to remove lye from Biodiesel
production. Water wash is required.
In all cases the centrifuge will de-water BUT on shut down you
MUST divert or catch the contents of the rotor before it stops
to prevent the water it will hold from draining back into the
now clean oil.
The use of extra rotors will speed up the process time. Dirty
rotors can be switched out in two minutes and then cleaned
after they cool. The cleaning of a rotor at 180F is difficult
and will take 15-30 minutes to cool.
Measures
12” wide by 42” tall and 16” deep to stand next to a 55 gallon
drum.
Model OPS-20
Click to enlarge
Cleaning rate: 55 gallons per hour
Measures 13” wide by 42” tall and 16” deep to stand next to a
55 gallon drum.
Shipping
weight: 70 pounds
Rotor
holding capacity: 10.5 oz of contamination.
Pump
and Motor Features: 100 PSI maximum continuous pressure,
all-bronze construction, bronze gears with stainless steel
shafts and mechanical seal. Motor is 1/3 hp USA manufactured
carbonator-mount motor, 115V-60Hz-1 phase, 1750 rpm, open,
drip-proof enclosure, automatic thermal overload protection.
Frame
is a 12 gage steel fully formed structure with only two weld
joints and polyester powder coating
Maximum Operating Temperature
of the pump is 210 degrees F/ 90c
OPS-20-Kit $1695
OPS-20-Assembled $1925
Model
OPS-50
Click to enlarge
Cleaning rate: 108 gallons per hour Measures
13” wide by 42” tall and 16” deep to stand next to a 55 gallon
drum.
Shipping
weight: 85 pounds
Rotor
holding capacity: 20 oz of contamination.
Pump
and Motor Features: 100 PSI maximum continuous pressure,
all-bronze construction, bronze gears with stainless steel
shafts and mechanical seal. Motor is 1/3 hp USA manufactured
carbonator-mount motor, 115V-60Hz-1 phase, 1750 rpm, open,
drip-proof enclosure, automatic thermal overload protection.
Frame
is a 12 gage steel fully formed structure with only two weld
joints and polyester powder coating
Maximum Operating Temperature
of the pump is 210 degrees F/ 90c
OPS-50-Kit
$1895
OPS-50-Assembled $2150
Model OPS-50x2
Click to enlarge
Cleaning rate: 216 gallons per hour Measures
13” wide by 42” tall and 24” deep to stand next to a 55 gallon
drum.
Shipping
weight: 150 pounds
System
holding capacity: 40 oz of contamination.
Pump
Features: 100 PSI maximum continuous pressure, all-bronze
construction, bronze gears with stainless steel shafts.
Motor
Features: 1 hp US manufactured electric motor,
115/230V-60Hz-1 phase, 1750 rpm, TEFC enclosure
Frame
is a 12 gage steel fully formed structure with only two weld
joints and polyester powder coating
Maximum Operating Temperature
of the pump is 210 degrees F/ 90c
OPS-50x2-Kit $3100
OPS-50x2-Assembled $3300
Consult your local dealer for delivery
information. Contact us
Made in USA
Dieselcraft is a
trade mark of The Magnum Group LLC
The Executive Order or the exemption it provides is not an
endorsement or approval of any emissions reduction claims for
the Fuel Stabilizer, and is only a finding that the device is
exempt from the prohibitions of Vehicle Code Section 27156
